DEADBUG LABS

APPS

The twelve IMP-1 firmware tools — what each one does, and where it actually stands. Statuses are taken from the build report, not the brochure.

> status_key

// 2026-11-16 — firmware clean build: 0 errors, 0 warnings. Boards are not fabricated yet, so nothing here has run on real IMP-1 hardware.

REAL — implemented and compiled in.

REAL — WITH CAVEAT — works, with the limit stated on its card.

UNVERIFIED — compiles; not yet proven against the thing it talks to.

NOT FITTED — STUB — the hardware is not on build 1; the menu refuses entry. Lands natively on IMP-2.

> the_tools

Sub-GHz

STATUS — REAL, WITH CAVEAT

CC1101 capture and replay of sub-GHz remote signals — band picker, live RSSI, files in the standard .sub format, transmit behind a confirm.

Capture is FIFO-based at 4.806 kBaud with an RSSI gate (the board has no edge-timing pin) — fine for OOK remote replay, not a logic analyser. The fitted antenna is 915 MHz.

NFC

STATUS — REAL, WITH CAVEAT

ST25R3916B front-end: poll cards, read UID/ATQA/SAK, dump NTAG to SD, test-write with re-read verify.

MIFARE Classic block operations are pending Crypto1 authentication — poll/UID and full NTAG support work now. Receiver tuning is set in situ at bring-up.

IR

STATUS — REAL

Learn remote-control signals and replay them — NEC decode with a raw fallback, library saved to SD in a standard .ir format, send behind a confirm.

BadUSB

STATUS — REAL

USB HID payload runner with a streaming DuckyScript interpreter (STRING / DELAY / REPEAT / key combos), plus a USB storage personality. Run and test-type are both confirm-gated.

GPIO

STATUS — REAL

Direct pin control under the firmware claim policy — driver-owned pins refuse, unrouted pads refuse, and the refusal shows on screen instead of failing silently.

U2F

STATUS — COMPILES, HOST INTEROP UNVERIFIED

A CTAP1 security-key engine: full CTAPHID transport, REGISTER and AUTHENTICATE, P-256 ECDSA signing, encoder-press user presence.

Stated plainly: this has never been tested against a live host. The attestation certificate is self-signed and hand-encoded, and strict FIDO checkers may reject it. It is the #1 verification item at bring-up — do not rely on it yet.

Archive

STATUS — REAL

File manager for everything the other tools save — browse the six tool folders on the microSD card, inspect sizes, delete behind a confirm.

Flash Lab

STATUS — REAL

Bench tool for the socketed SPI flash: RDID-first identification, chunked dumps with progress, verified write tests — and the physical WP# lock is respected; a locked chip stops the tool, by design.

Security Auto-Audit

STATUS — REAL — PASSIVE ONLY

An inventory and resilience check for your own gear: Wi-Fi and BLE inventory, watch-your-own-AP logging, and a camera resilience checklist, written up as a report on SD.

Passive only — it observes and records. There is no deauth, no jamming, and no connection attempts anywhere in the code.

RFID

STATUS — NOT FITTED — STUB

125 kHz RFID. The front-end is not on build 1, so the firmware carries a guarded stub and the menu refuses entry.

Lands natively on IMP-2.

iButton

STATUS — NOT FITTED — STUB

Dallas key reader. Not fitted on build 1 — guarded stub, menu refuses entry.

Lands natively on IMP-2.

1-Wire

STATUS — NOT FITTED — STUB

1-Wire bus devices. Not fitted on build 1 — guarded stub, menu refuses entry.

Lands natively on IMP-2.

Full per-module detail: the build report in the firmware repo.

> responsible_use

Responsible use — Deadbug Labs products are tools for testing systems you own or have explicit authorization to test. Testing systems that do not belong to you, without authorization, is illegal. By purchasing, you agree to use these products only on your own systems or systems you are authorized to test, and you accept full responsibility for how you use them. Deadbug Labs is not liable for misuse.